Bintaotne 1Port GEPON ONT Setup and Configuration Manual
ONT is also called ONU. ONT full form is Optical network Termination and ONU full form is the Optical Network Unit. Both are the same used for end-user fiber network termination with the Gpon solution. This post belongs to all brand ONT and ONT devices because all devices have the same chipset as ZTE and Huawei chipset. This manual helps you to guide GEPON ONT Configuration for the first time.
Gpon Huawei ONT and ONU setup and configuration. fiber network increasing very rapidly today and with the fiber network, we can deliver internet speed of more than Gbps. So we required Fiber OLT, ONT, ONU, Fiber Patchcord, and Fiber Splitter. The process of Binatone 1port GEPON ONT configuration step to step. Binatone BTE801 ONT is based on ZTE Chipset so you can get the user guide for all ZTE-based ONT and ONU Devices.
- How to Connect Any Wi-Fi without Password from Mobile?
- Jio Giga Fiber Router WiFi Password and Name Change
Binatone 1port GEPON ONT Default Settings
- Binatone BTE801 ONT Default IP Address is: 192.168.1.1
- Default username / password : admin/admin
- The 5 Important Tools for Design, Installation and Manage Fibre Networks
- Best GPON and EPON OLT (Optical Line Terminal) for Fiber Network
1Port GEPON ONT (ZTE)Connection and Login
Connect ONT with Power Adaptor Comes with Device. And connect the LAN port to PC/Laptop. Follow the picture given below to connect the ONT /ONU connection.
See Also – How to configure Syrotech GEPON OLT and EMS Software installation
Use PC/Laptop Lan IP Address 192.168.1.x series
EXP: you can use 192.168.1.2 to 254
See How to Configure Laptop IP Address
Login ONT
Open the Browser and Use the 192.168.1.1 IP address to open the ONT web interface.
Use admin/admin to login the device.
ZTE Chipset 1 Port GEPON ONT LAN configuration
After Login ONT device will by default go in the status page. For LAN configuration click on Network tab. follow given the picture.
LAN IP ADDRESS: Change the IP in this box
ENABLE DHCP Server: Check the box for enabling the DHCP server
Click Submit to Save change all settings
1PORT GEPON ONT WAN Configurations:
For WAN configuration go to NETWORK–> WAN
Connection name: use any name for the new WAN connection
Enable VLAN: if your OLT is configured with VLANs then enable VLAN option and put VLAN id for the network.
Router: Choose Rout for router mode
Link Type: user PPP, PPPoE, Static or DHCP for your Link type as per your network configuration.
Binatone 1Port GEPON ONT VLAN configuration
Instead of configuring VLAN in ONT device setup VLAN with olt configuration so ONT device can auto-configured remotely without visiting the client site.
VLAN Mode setting is available in
Network–>Port Configuration –> VLAN
Here you can set the VLAN mode type. EXP: if you are using tag then select tag, if using trunk then you can choose trunk etc.. choose according to your network configuration.
How to Configure Port Negotiations setting in GEPON ONT and ONU
Port config for port negotiation speed.
Go to Network –>Port Configuration–>Mode
Choose Auto for auto settings
select manually speed for manual port config selection
Binatone 1Port GEPON ONT PON configuration:
Network–> PON
Use LOID name and Password.
How to set Rate Limit in 1Port GEPON ONT/ONU
Go to Network–>Port Config–> Rate Limitation
Choose your Port from Port option and put rate limit for both options.
Ingress rate limitation and DS rate limitation. By default, its comes with a maximum rate limit of 1024000 for both options.
How to Enable Loop Detection in Binatone 1Port GEPON ONT
Loop Detection setting will help you to avoid loop issues in the network. If loop detection is enabled then the port will auto-disable if get any looping issue in the network and after some time it again be rechecked for network loop issues.
Go to Administration –> Loopback Detection –->Enable Configuration
Enable the option from LAN1
How to Factory Default Binatone BTE801 1Port GEPON ONT
Go to Administration –>System Management
Reboot: you can software reboot ONT from this button
Restore Default: Restore Default will erase all settings and the device will be in factory mode.
ZTE 1Port GEPON ONT Firmware Up-gradation.
Go to Administrator –>System Management –>Software Upgrade
To setup ONT configuration remotely from an OLT device you need to go through your brand OLT configuration guide to create a profile in OLT
Related post
- how to fix internet connection problems and WiFi Problems
- How to Integrate CCTV Camera With Fiber Optic Network
- 5 Best Long-Range Wireless Point to Point Device for Internet and CCTV