How to setup Flying Voice G201N4 Mini VoIP Wireless Router (with Picture)

Flying Voice G201N4 Mini VoIP Wireless Router Configuration
(Last Updated On: February 24, 2018)

Flying Voice G201N4 Mini VoIP Wireless Router Configuration.

Flying Voice G201N4 mini VoIP Router supported 1 FXS 4 LAN port 1 USB port and WLAN, G201N4 supported 5Volt 2Amp DC, it’s a Voice over  internet protocol  router with Wi-Fi and Ethernet supported for wired connection, G201N support sip server and Wan support Dynamic, PPPoE, static IP. G201N4 is able to make calls via SIP proxy voice communications, plus the IP sharing, and the QoS mechanism. USB port can make user to connect external storage devices make easy to share file via Flying Voice VoIP Wireless router. Its comes with 2dBi Omni Directional Inbuilt Antenna for IEEE802.11n 1T1R Wireless which provide internet  Wi-Fi Access. If you are looking for configuration of any flying voice routers then you are on right place .here you will get complete manual of Flying Voice G201N4 Mini VoIP Wireless Router Configuration.

Flying Voice G201N4 Mini VoIP Wireless Router can be configured three ways, as follows:

(1)Use IVR

(2)Use Web

(3)Use Provision.

 

Please see Flying Voice G201N4 Mini VoIP Wireless Router Manual to use IVR configuration.

 

Flying Voice G201N4 Mini VoIP Wireless Router Manual | Download

Web Configuration:  Voice G201N4  Mini VoIP Wireless Router

Default IP is 192.168.1.1  and default username admin, password is admin also. To proceed to web configuration please go throw the network connection of G201N4  VoIP Wireless Router.

Step 1.Connect Line port to land line jack with a RJ-11 cable.

Step 2.Connect the WAN port to a modem or switch or router or Internet with an Ethernet cable.

Step 3.Connect one port of 4 LAN ports to your computer with a RJ-45 cable. This device allows you to connect 4 PCs directly.

Step 4.Connect one end of the power cord to the power port of this device. Connect the other end to the wall outlet of electricity.

Step 5.Check the Power and WAN, LAN LEDs to assure network connections

 

Access Flying Voice Router to web:

After proper connection of router open go to your Laptop/Pc and put 192.168.1.X series IP address to Lan IPv4 Properties.

See how to configure IP Address in Laptop / PC Lan

 Flying Voice G201N4

Flying Voice G201N4 Mini VoIP Wireless Router Network Configuration.

Go to WAN- Configure your ISP IP address

Choose the your internet type such as PPPoE, DHCP, Static mode-

If you do not know about it contact your internet provider and as for details about PPPoE username password, Static IP address and other details.

LAN: use private IP series to local IP Address.

Flying Voice G201N4 Mini VoIP Wireless Router

Flying Voice G201N4 Mini VoIP Wireless Router Wireless Configuration.

Follow the below picture for Wireless Configuration

Wireless Connection Mode – AP (Access point should select for Wi-Fi AP)

SSID – type wireless Name for flying voice Wi-Fi network name in SSID box

Frequency (Channel)-  if you are using single router you can keep it auto mode but if you are using more than one Wi-Fi router user channel number 1,6,11 to avoid interference due to overlapping of frequency.

After done all settings click Save an apply button.

Flying Voice G201N4 Mini VoIP Wireless Router Manual Download

Flying Voice G201N4  Mini VoIP Wireless Router SIP Configuration.

Go to SIP account –> SIP setting

how to configure multiple sip in flying voive router

Flying Voice G201N4 Mini VoIP Wireless Router Configuration of Phone.

Go to Phone –>Preferences

Regional – Choose your country from list

Fill the setting as per your country telecom supported parameters.

How to configure Phone in Flying Voice Voip Mini Router

Flying Voice G201N4  Mini VoIP Wireless Router  Configuration of Security .

In security feature you can configuration of content filtering and pot forwarding rule.

Flying Voice G201N4 Mini VoIP Wireless Router Configuration of Security.

In security feature you can configuration of content filtering and pot forwarding rule.

How to Prot Forward in Flying Voice G201N4 Mini VoIP Wireless Router

Flying Voice G201N4  Mini VoIP Wireless Router USB Configuration.

USB  port to enable network sharing for your flash drive into network.

how to Mount USB pen drive in flying voice Voip router

Flying Voice G201N4 Mini VoIP Wireless Router Administration Configuration.

Administration provides to upgrade firmware, change user, and many other services which required in network.

 

Backup and Restore Configuration file

Backup configuration option gives a safe option to keep your one time configuration for further. Configuration Backup file required whenever you want to change flying voice outer due to miss behaving or break down. This steps save your lots of time and exercise to reconfiguring your router again when you need to replace it. You need to just download config file after finish configuration and restore it to new router.

1: To download configuration file go to Administrator tab and Save config File option

Click Download button to save configuration file in driver. Move it to save place so you can use it next time if your router factory reset or break down.

 

Restore Config file– To restore configuration file click Browse button and select configuration file you have taken backup last time and click Upload button to restore settings.

Router will take 20-30 second to restore settings and after reboot your router will configured with settings.

 

Flying Voice G801 Router Manual (Setup & Configuration)

 

2: Flying Voice Administrator Settings

Administrator settings include access of router with admin rights. You can create and change access password for your router with this settings.

User Type– choose the user type you want to change or create username and password

New username – type username for selected user type

New password- type password for same user you want to create

Confirm password- password confirmation for same user name.

 

3- Language:

You can change your router language as per your country language. Go to language tab and select your language from list.

 

4: VPN Access –

If your network running in VPN network you can enable management access with your VPN tunnel to manage your flying voice.

Management using VPN- enables this option

 

5- WEB Access

By default remote web login disabled for most of routers due to security reason but you can enable it as per your choice from administrator tab.

Remote Web Login – enable this option ( if its disable you cannot access your router remotely through web interface)

Web port – by default 80 (you can change port number according your network if already used 80 with some other server or devices)

 

Related Post

10 Best free and Paid Antivirus for Windows, Mac OS and Androids Phone

 

Be the first to comment

Leave a Reply

Your email address will not be published.


Please type the characters of this captcha image in the input box

Please type the characters of this captcha image in the input box

*


This site uses Akismet to reduce spam. Learn how your comment data is processed.